We've stumbled on this article about Installing A Bathtub down the page on the net and think it made good sense to talk about it with you on my blog.
Setting up a tub isn't precisely rocket science, but it does require solid plumbing, woodworking, as well as in some cases, tiling skills. Changing an old bath tub with a brand-new one is additionally a reasonably tough job. If the old bathtub is conveniently easily accessible, the project can move rapidly; if you need to open up a wall surface to get rid of the old tub and also place the new bathtub, the task is much harder. In either situation, the job is within a residence handyman's abilities, although you will need an assistant to leave the old bathtub and also embeded in the brand-new one. See to it you have actually qualified on your own for the work and also fit trying it. As opposed to employing a specialist to take control of a halfway-completed job, it is better to think about utilizing one prior to you start. Chances are you may need a specialist plumber to make tube links.
This write-up will certainly help you install a new tub in your shower room if you have actually currently acquired a brand-new tub and don't need to change the plan of your previous water system pipelines.
Your devices and also product list need to consist of the following:
Getting ready for the Setup
First of all, the supporting framework supplied with the bath must be fitted (if called for) according to the supplier's guidelines. Next off, fit the faucets or mixer to the bath tub. When fitting the tap block, it is essential to ensure that if the tap includes a plastic washing machine, it is fitted in between the bathroom as well as the taps. On a plastic bathroom, it is also practical to fit a sustaining plate under the faucets device to stop pressure on the bath tub.
Fit the adaptable faucet adapters to the bottom of both faucets making use of 2 nuts and olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet via the hole in the bathroom. Make use of the nut provided by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bath. Ensure you use every one of the provided washers.
Connect the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bath ought to now be ready to be fitted in its final position.
Removing Old Taps
If you require to change old faucets with brand-new ones as a part of your installment, then the first thing you ought to do is detach the supply of water. After doing so, switch on the taps to drain pipes any kind of water continuing to be in the system. The procedure of eliminating the existing taps can be fairly bothersome as a result of the limited gain access to that is often the situation.
Use a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipes to the taps. Have a fabric ready for the continuing to be water that will certainly come from the pipelines. Once the supply pipelines have been gotten rid of, make use of the exact same device to loosen the nut that holds the taps onto the bath/basin. You will require to quit the single taps from transforming throughout this procedure. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will need to be cleansed of any type of old sealing compound.
Prior to moving on to fit the brand-new faucets, compare the pipeline connections on the old faucets to the new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the new taps to fit.
Installing the Bathtub
Using both wooden boards under its feet, put the bathtub in the required placement. The wooden boards are valuable in uniformly spreading out the weight of the tub over the area of the boards as opposed to concentrating all the weight onto 4 little points.
The next objective is to guarantee that the bathtub is leveled all round. This can be achieved by checking the level and adjusting the feet on the tub until the spirit level checks out level.
To mount faucets, fit all-time low of the furthest adaptable tap connector to the appropriate supply pipe by making a compression sign up with; then do the exact same for the various other tap.
Turn on the water system and examine all joints and also brand-new pipework for leakages and also tighten them if necessary. Fill the bath tub and additionally inspect the overflow outlet as well as the regular electrical outlet for leakages.
Lastly, deal with the bath paneling as defined in the producer's user's manual. Tiling as well as securing around the bathtub must wait until the bathtub has been utilized at the very least once as this will resolve it into its final placement.
Fitting New Taps
If the tails of the brand-new faucets are plastic, after that you will require a plastic port to prevent damage to the string. One end of the connector fits on the plastic tail of the tap as well as the various other end offers a link to the current supply pipes.
If you need to fit a monobloc, after that you will certainly require minimizing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next off, place the faucet in the mounting hole in the bath/basin making sure that the washers remain in area in between the tap and the sink. Protect the faucet in place with the manufacturer supplied backnut. As soon as the faucet is safely in position, the supply pipelines can be linked to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with normal tap connectors. The previous kind should be attached to the faucet ends initially, tightening up only by hand. The supply pipes can later on be attached to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Bath tub
In the location where the bathroom satisfies the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is very important as the fitting can move enough to fracture a rigid seal, triggering the water to penetrate the wall surface in between the bathroom and the tiling, causing problems with moisture and also feasible leakages to the ceiling listed below.
You can choose from a variety of coloured sealants to blend in your components and also installations. They are marketed in tubes as well as cartridges, as well as can sealing voids as much as a width of 3mm (1/8 inch). If you have a larger void to load, you can fill it with spins of drenched newspaper or soft rope. Keep in mind to constantly fill up the tub with water before sealing, to permit the activity experienced when the bathtub is in use. The sealer can split relatively early if you do not consider this activity prior to securing.
Additionally, ceramic coving or quadrant tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also quickly available on the marketplace. It is suggested to fit the ceramic tiles using waterproof or water resistant adhesive as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We are very serious about Installing A Bathtub and I'm hoping you enjoyed our page. Enjoyed our blog? Please share it. Let someone else discover it. I truly appreciate reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Request An Appointment